1 ? features ? this circuit is processed in accordance to mil-std- 883 and is fully conformant under the provisions of paragraph 1.2.1. high slew rate . . . . . . . . . . . . . . . . . . . . . . .50v/ s (min) 65v/ s (typ) wide power bandwidth . . . . . . . . . . . . . . . 750khz (min) low offset current . . . . . . . . . . . . . . . . . . . . 25na (min) 10na (typ) high input impedance . . . . . . . . . . . . . . . . . 50m ? (min) 100m ? (typ) wide small signal bandwidth. . . . . . . . . . .12mhz (typ) fast settling time (0.1% of 10v step) . . . . 250ns (typ) low quiescent supply current . . . . . . . . . . 6ma (max) internally compensated for unity gain stability applications data acquisition systems rf amplifiers video amplifiers signal generators pulse amplification description the ha-2510/883 is a high performance operational ampli- fier which sets the standards for maximum slew rate and wide bandwidth operation in moderately powered, internally compensated, monolithic devices. in addition to excellent dynamic characteristics, this dielectrically isolated amplifier also offers low offset current and high input impedance. the 50v/ s minimum slew rate and fast settling time of the ha-2510/883 are ideally suited for high speed d/a, a/d, and pulse amplification des igns. the ha-2510/883?s supe- rior bandwidth and 750khz minimum full power b andwidth are extremely useful in rf and video applications. to insure compliance with slew rate and transient response specifica- tions, all devices are 100% tested for ac performance char- acteristics over full temperature limits. to improve signal conditioning accuracy, the ha-2510/883 provides a maxi- mum offset current of 25na and a minimum input impedance of 50m ? , both at 25 o c, as well as offset voltage adjust capa- bility. pinout ordering information part number temp. range ( o c) package pkg. no. ha7-2510/883 -55 to 125 8 ld cerdip f8.3a ha-2510/883 (cerdip) top view 1 2 3 4 8 7 6 5 comp v+ out bal bal -in +in v- + - october 26, 2004 spec number 511003-883 fn3697.3 caution: these devices are sensitive to electrostatic discharge; follow proper ic handling procedures. 1-888-intersil or 321-724-7143 | intersil (and design) is a registered trademark of intersil americas inc. copyright ? intersil americas inc. 2002, 2004. all rights reserved ha-2510/883 high slew rate operational amplifier
2 absolute maximum ratings thermal information voltage between v+ and v- terminals . . . . . . . . . . . . . . . . . . . . 40v differential input voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15v voltage at either input terminal . . . . . . . . . . . . . . . . . . . . . . v+ to v- peak output current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50ma esd rating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <2000v operating conditions temperature range . . . . . . . . . . . . . . . . . . . . . . . . . -55 o c to 125 o c supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15v v incm 1/2 (v+ - v-) r l 2k ? thermal resistance (typical, note 1) ja jc cerdip package . . . . . . . . . . . . . . . . . . 120 o c/w 30 o c/w package power dissipation limit at 75 o c for t j 175 o c cerdip package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 870mw package power dissipation derating factor above 75 o c cerdip package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.7mw/ o c maximum junction temperature . . . . . . . . . . . . . . . . . . . . . . . 175 o c maximum storage temperature range . . . . . . . . . .-65 o c to 150 o c maximum lead temperature (soldering 10s) . . . . . . . . . . . . . 300 o c caution: stresses above those listed in ?absolute maximum ratings ? may cause permanent damage to the device. this is a stress o nly rating and operation of the device at these or any other conditions above those indicat ed in the operational sections of this specification is not impl ied. note: 1. ja is measured with the component mounted on a low effective thermal conductivity test board in free air. see tech brief tb379 for details. table 1. dc electrical performance characteristics device tested at: v supply = 15v, r source = 100 ? , r load = 500k ? , v out = 0v, unless otherwise specified. parameter symbol conditions group a subgroups temp ( o c) min max units input offset voltage v io v cm = 0v 1 25 -8 8 mv 2, 3 125, -55 -18 10 mv input bias current +i b v cm = 0v, +r s = 100k ? , -r s = 100 ? 1 25 -200 200 na 2, 3 125, -55 -400 400 na -i b v cm = 0v, +r s = 100 ? , -r s = 100k ? 1 25 -200 200 na 2, 3 125, -55 -400 400 na input offset current i io v cm = 0v, +r s = 100k ? , -r s = 100k ? 1 25 -25 25 na 2, 3 125, -55 -50 50 na common mode range +cmr v+ = 5v, v- = -25v 1 25 +10 - v 2, 3 125, -55 +10 - v -cmr v+ = 25v, v- = -5v 1 25 - -10 v 2, 3 125, -55 - -10 v large signal voltage gain +a vol v out = 0v and +10v, r l = 2k ? 42510-kv/v 5, 6 125, -55 7.5 - kv/v -a vol v out = 0v and -10v, r l = 2k ? 42510-kv/v 5, 6 125, -55 7.5 - kv/v common mode rejection ratio +cmrr ? v cm = +10v, v+ = +5v, v- = -25v, v out = -10v 12580-db 2, 3 125, -55 80 - db -cmrr ? v cm = -10v, v+ = +25v, v- = -5v, v out = +10v 12580-db 2, 3 125, -55 80 - db ha-2510/883 spec number 511003-883
3 output voltage swing +v out r l = 2k ? 42510-v 5, 6 125, -55 10 - v -v out r l = 2k ? 425--10v 5, 6 125, -55 - -10 v output current +i out v out = -10v 4 25 10 - ma 5, 6 125, -55 7.5 - ma -i out v out = +10v 4 25 - -10 ma 5, 6 125, -55 - -7.5 ma quiescent power supply current +i cc v out = 0v, i out = 0ma 125-6ma 2, 3 125, -55 - 6.5 ma -i cc v out = 0v, i out = 0ma 125-6-ma 2, 3 125, -55 -6.5 - ma power supply rejection ratio +psrr ? v sup = 10v, v+ = +20v, v- = -15v, v+ = +10v, v- = -15v 12580-db 2, 3 125, -55 80 - db -psrr ? v sup = 10v, v+ = +15v, v- = -20v, v+ = +15v, v- = -10v 12580-db 2, 3 125, -55 80 - db offset voltage adjustment +v io adj note 2 1 25 v io -1 - mv 2, 3 125, -55 v io -1 - mv -v io adj note 2 1 25 v io +1 - mv 2, 3 125, -55 v io +1 - mv note: 2. offset adjustment range is [v io (measured) 1mv] minimum referred to output. this test is for functionality only to assure adjustment through 0v. table 2. ac electrical performance characteristics device tested at: v supply = 15v, r source = 50 ? , r load = 2k ? , c load = 50pf, a vcl = +1v/v, unless otherwise specified. parameter symbol conditions group a subgroups temp ( o c) min max units slew rate +sr v out = -5v to +5v, 25% +sr 75% 7 25 50 - v/ s 8a, 8b 125, -55 45 - v/ s -sr v out = +5v to -5v, 75% -sr 25% 7 25 50 - v/ s 8a, 8b 125, -55 45 - v/ s table 1. dc electrical performance characteristics (continued) device tested at: v supply = 15v, r source = 100 ? , r load = 500k ? , v out = 0v, unless otherwise specified. parameter symbol conditions group a subgroups temp ( o c) min max units ha-2510/883 spec number 511003-883
4 spec number 511003-883 rise and fall time t r v out = 0 to +200mv, 10% t r 90% 7 25 - 50 ns 8a, 8b 125, -55 - 60 ns t f v out = 0 to -200mv, 10% t f 90% 7 25 - 50 ns 8a, 8b 125, -55 - 60 ns overshoot +os v out = 0 to +200mv 7 25 - 40 % 8a, 8b 125, -55 - 50 % -os v out = 0 to -200mv 7 25 - 40 % 8a, 8b 125, -55 - 50 % table 3. electrical performance characteristics device characterized at: v supply = 15v, r load = 2k ? , c load = 50pf, unless otherwise specified. parameter symbol conditions notes temp ( o c) min max units differential input resistance r in v cm = 0v 3 25 50 - m ? full power bandwidth fpbw v peak = 10v 3, 4 25 750 - khz minimum closed loop stable gain clsg r l = 2k ? , c l = 50pf 3 -55 to 125 1 - v/v quiescent power consumption pc v out = 0v, i out = 0ma 3, 5 -55 to 125 - 195 mw notes: 3. parameters listed in table 3 are controll ed via design or process parameters and ar e not directly tested at final production. these param- eters are lab characterized upon initial design release, or upon design changes. these parameter s are guaranteed by characteriz ation based upon data from multiple production runs which reflect lot to lot and within lot variation. 4. full power bandwidth guarantee based on slew rate measurement using fpbw = slew rate/(2 v peak ). 5. quiescent power consumption based upon quiescent s upply current test maximum. (no load on outputs.) table 4. electrical test requirements mil-std-883 test requirements subgroups (see tables 1 and 2) interim electrical parameters (pre burn-in) 1 final electrical test parameters 1 (note 6), 2, 3, 4, 5, 6, 7, 8a, 8b group a test requirements 1, 2, 3, 4, 5, 6, 7, 8a, 8b groups c and d endpoints 1 note: 6. pda applies to subgroup 1 only. table 2. ac electrical performance characteristics (continued) device tested at: v supply = 15v, r source = 50 ? , r load = 2k ? , c load = 50pf, a vcl = +1v/v, unless otherwise specified. parameter symbol conditions group a subgroups temp ( o c) min max units ha-2510/883
5 die characteristics die dimensions: 65 mils x 57 mils x 19 mils 1650 m x 1450 m x 483 m metallization: type: al, 1% cu thickness: 16k ? 2k ? glassivation: type: nitride (si3n4) over silox (sio2, 5% phos.) silox thickness: 12k? 2k? nitride thickness: 3.5k? 1.5k? worst case current density: 0.3 x 10 5 a/cm 2 substrate potential (powered up): unbiased transistor count: ha-2510/883: 40 process: bipolar dielectric isolation metallization mask layout ha-2510/883 v- +in out bal -in v+ comp bal ha-2510/883
6 burn-in circuit ha7-2510/883 r 1 = 1m ? , 5%, 1/4w (min) c 1 = c 2 = 0.01 f/socket (min) or 0.1 f/row (min) c 3 = 0.01 f/socket (10%) d 1 = d 2 = 1n4002 or equivalent/board |(v+) - (v-)| = 30v v+ c 1 d 1 r 1 d 2 c 2 v- + - 1 3 4 8 7 6 5 2 c 3 ha-2510/883
7 all intersil semiconductor products are manufactured, assembled and tested under iso9000 quality systems certification. intersil products are sold by description only. intersil corporation reserves the right to make changes in circuit design and/o r specifications at any time without notice. accordingly, the reader is cautioned to verify that data sheets are current before placing orders. information furnished by int ersil is believed to be accurate and reli- able. however, no responsibility is assumed by intersil or its subsidiaries for its use; nor for any infringements of patents o r other rights of third parties which may result from its use. no license is granted by implication or otherwise under any patent or patent rights of intersil or its sub sidiaries. for information regarding intersil corporation and its products, see web site http://www.intersil.com ha-2510/883 notes: 1. index area: a notch or a pin one identification mark shall be locat- ed adjacent to pin one and shall be located within the shaded area shown. the manufacturer?s identification shall not be used as a pin one identification mark. 2. the maximum limits of lead di mensions b and c or m shall be measured at the centroid of the finished lead surfaces, when solder dip or tin plat e lead finish is applied. 3. dimensions b1 and c1 apply to lead base metal only. dimension m applies to lead plating and finish thickness. 4. corner leads (1, n, n/2, and n/2+1) may be configured with a partial lead paddle. for this co nfiguration dimension b3 replaces dimension b2. 5. this dimension allows for off- center lid, meniscus, and glass overrun. 6. dimension q shall be measured from the seating plane to the base plane. 7. measure dimension s1 at all four corners. 8. n is the maximum number of terminal positions. 9. dimensioning and tolerancing per ansi y14.5m - 1982. 10. controlling dimension: inch. bbb c a - b s c q l a seating base d plane plane -d- -a- -c- -b- d e s1 b2 b a e m c1 b1 (c) (b) section a-a base lead finish metal e a/2 a m s s ccc c a - b m d s s aaa ca - b m d s s e a ceramic dual-in-line frit seal packages (cerdip) f8.3a mil-std-1835 gdip1-t8 (d-4, configuration a) 8 lead ceramic dual-in-line frit seal package symbol inches millimeters notes min max min max a - 0.200 - 5.08 - b 0.014 0.026 0.36 0.66 2 b1 0.014 0.023 0.36 0.58 3 b2 0.045 0.065 1.14 1.65 - b3 0.023 0.045 0.58 1.14 4 c 0.008 0.018 0.20 0.46 2 c1 0.008 0.015 0.20 0.38 3 d - 0.405 - 10.29 5 e 0.220 0.310 5.59 7.87 5 e 0.100 bsc 2.54 bsc - ea 0.300 bsc 7.62 bsc - ea/2 0.150 bsc 3.81 bsc - l 0.125 0.200 3.18 5.08 - q 0.015 0.060 0.38 1.52 6 s1 0.005 - 0.13 - 7 90 o 105 o 90 o 105 o - aaa - 0.015 - 0.38 - bbb - 0.030 - 0.76 - ccc - 0.010 - 0.25 - m - 0.0015 - 0.038 2, 3 n8 88 rev. 0 4/94
|
